How To Change A Crew Neck Into A V Neck

Download Article

V-necked collars are very flattering on almost people. They draw the heart toward the face up and elongate the body. You tin plow whatsoever crew-necked t-shirt into a 5-cervix using a seam ripper, fabric scissors, pins and some bones sewing skills.

one

Gather your materials. To complete the project, you volition need a crew-necked shirt, a ruler or measuring record (if using a tape mensurate, you lot'll besides need a split straight border), stick pins, a fabric mark, cloth pair of scissors, a seam ripper, thread the same color every bit your shirt, a sewing car or sewing needle.
2
Measure the V. An easy way to do this is to utilise a V-necked shirt that you like every bit a guide. Fold the shirt vertically in half, making certain that the shoulders line up. Lay it flat on a table.Then use a ruler to measure the altitude from the signal where the collar meets the shoulder seam to the point of the V. Write down this measurement.
- If you don't take another v-necked shirt, you lot'll have to estimate how deep the V should be. In this case, it's better to start conservatively as you can always brand it deeper.^[1]
- Yous may want to attempt on the shirt to estimate how deep you want the V. While wearing the shirt, look in the mirror and mark the spot y'all'd like the point of the V with a pin.
Advertisement
3

Fold your crew-neck shirt vertically. The front of the collar should be on the exterior of the fold. Make sure that the neckline, the shoulders and the artillery match upwards exactly. Lay it out on a table, smoothing it down until it is costless of wrinkles.
4
Trace the V. Place a ruler in a diagonal line from the the betoken where the shoulder seam meets the collar downwards to the middle of the chest. Using the measurements you took in the previous footstep, mark off the point of the "V" with a fabric marking. And then depict a line between the mark and the signal where shoulder seam meets the neckband.
- Flip the shirt over and repeat this step on the other side.
Advertizing

ane
Remove the stitches. Unfold the shirt, turn it inside-out and lay it on the table. Make sure that the front end side is facing you. So apply a seam ripper to remove the stitches securing the forepart side of the neckband to the shirt.
- If you don't have a seam ripper, you can apply a abrupt pair of scissors to advisedly cut it abroad.
- Stop at the shoulder seams. Unless you don't programme to re-attach it to your new neck-line, leave the collar attached to the back of the shirt.
2

Smooth the crew-neck shirt out on the tabular array. Brand certain the continued collar is folded back, abroad from where you volition cut.^[two] Doing so ensures the smoothest and straightest cuts and helps you avoid mistakes.
iii
Cut out the V-neck. Starting on one side of the 5, apply a pair of sharp scissors and cut along the marked line. Stop when you achieve the bottom. Repeat this procedure on the other side. Be careful to only cutting through the front side of the shirt.
- If y'all didn't plan on creating a hemmed collar, your new shirt is done.
Ad

1

Cut the front of the detached crew collar in the center. You'll demand to first determine where the center is. To practise this, lay the t-shirt flat with the front facing you. Measure the width of the collar, and using your fabric marker place a dot in the centre. This is where yous will cut.
2

Stretch each side of the cut collar along the length of your V-neck. Most crew-neck t-shirt collars are ribbed and should give several inches.
3
Pin the rough border of the collar to the shirt. Stretch i side at a time along the length of the V, pining equally y'all go. Place pins approximately every inch (two.5 cm) to brand sure the collar stretches and stays before yous stitch it. ^[3] Do the same thing on the other side.
- The crude edge of the collar should be paired with the rough edge of the t-shirt, with the edge of the collar facing the exterior of the shirt.
iv
Stitch from the meridian of the collar down to the bottom of the V. Run up approximately a quarter inch (0.6 cm) from the edge of the 2 layers.^[4] When you stitch downward the second side of the neckband, cease just a little before you become to the V and sew that terminate to the dorsum of the first side. Terminate by pressing the new hem downwardly with an atomic number 26.
- Make sure the thread in your sewing machine matches the color of the shirt.
- If yous don't have a sewing automobile, y'all can also hand sew the sides of the neckband to the sides of the 5.
Advertisement

Add New Question

Question

Is the shirt supposed to be inside out when I sew?

Yes. After you cease sewing it, you lot'll plough it right side out and and then there will be a make clean seam.

Inquire a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Video

Thanks for submitting a tip for review!

Things You'll Need

Flat surface
Fabric marker
Seam ripper
Ruler/straight border
Fabric scissors
Pins
Sewing automobile
Thread
Needle
Fe
Ironing board

Most This Article

Article Summary X

To cut a t-shirt into a V-neck, first by using a 5-neck shirt you already accept as a guide for where to mark the "V" on the t-shirt. Subsequently you've traced the "V," employ sharp scissors to remove the stitches securing the forepart of the collar. Side by side, cut out the V-neck, then cut the discrete collar down the middle, stretch it along where you marked the "V," and pivot it in identify. Finally, sew it down, starting at the top of the collar and placing the stitch about 1/iv inch from the border of the layers. To learn how to brand sure your stitching is flat and even, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 361,252 times.